Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - Tyler Steinmetz

Pages: [1] 2
1
Driveline / Wheels?
« on: November 18, 2014, 03:22:00 pm »
im just curious where i can get a cooler looking pair of wheels! bead locks or a cool looking design in the center. 4on4 bolt patter or 4on110, but has to be 8x8.. i know some fourwheelers have that bolt pattern. but having hard time finding anything. and also looking for fronts, if theres any cooler designs out there for front wheels. 6x6.5 wheels


2
USLMRA Races / Gp-t
« on: October 02, 2014, 12:00:43 am »
So, is the Gp twin and official national class!?

3
Briggs Flathead / Sp motor worth what???
« on: September 29, 2014, 11:57:43 pm »
Recently  bought a sp and I would be interest in selling motor.  Motor has mild porting. Gteam built motor.. Only thing I noticed it didn't have was the arc weights, but crank has been balanced, has spring kit in it, has hi torque starter. Higher comp than stock, but not much! Has arc rod. Has a billet flywheel. That's all I know about this motor. What's it worth? And it took 2nd place in mn points!

4
USLMRA Races / superstock twin?
« on: September 29, 2014, 08:40:33 pm »
is the superstock and superstock twin still a USLMRA class? i was lookin in rule book and cant find anything about them.

5
Briggs Flathead / oppy performance parts
« on: September 28, 2014, 11:09:50 pm »
where can i build a OPPY, cams and rods? anyplaces out there deal stuff for the oppys? thanks in advance!

6
Briggs OHV & Vanguard / Opposed twin flywheels
« on: September 27, 2014, 09:09:30 pm »
Was just curious if v-twin and opposed twin have the same billet flywheels?

7
Chassis / FXS gas pedal..
« on: July 20, 2014, 06:17:17 pm »
hello guys, i currently am using a hand throttle as a throttle and it sucks to hang onto this wild ride. can someone please explain how to make a gas pedal or send me some pictures of a gas pedal? is there any kits available for them or not??? my gas pedal would be on the left side of the mower(sitting on it)

8
Driveline / Gear ratio?
« on: July 02, 2014, 07:25:17 pm »
What is the known final gear ratio for a super stock twin! Any help be nice. Thanks in advance

9
Kohler Engines / Billet flywheel rules!
« on: July 02, 2014, 02:07:39 am »
If I'm running a twin in super stock twin class, which is ungoverned. Is it a uslmra rule to have a billet flywheel. I heard that arma is like that, but is it legal in uslmra or recommended?

10
Honda and Clone Engines / help... gx440 carb selection
« on: June 24, 2014, 09:24:21 pm »
hey guys, ive been building a gx 440, its cammed with a fully built valve train, and a arc rod(stock length), and its port and polished, ive tried running the HR tillotson carb, but i keep blowing out diaphragms it seems, ive tried running mikuni slide carbs, and nothing seems to work... what are you guys running? or can  get my HR built up from someone to make it work.. id love to use that HR but its no good if it wont hold up. and help is appreciated. Thanks in advance

11
Chassis / Fxs steering help...
« on: June 16, 2014, 09:40:44 pm »
I'm having some steering issues on my Fxs, fresh build. I got bout a 2 foot shaft going through a heim and into a universal joint, then on the other end of that joint is another rod going down, on the bottom I have a bent plate that goes back under my frame and that's where tie rods connects, it turns super hard and I was looking it's actually wrecking my u joint from all the pressure trying to turn the tires.. Any ideas or pictures would help.. Please

12
Honda and Clone Engines / governor removal...
« on: April 26, 2014, 09:25:36 pm »
i was revving my new motor, gx440 gen 2. and noticed it maxes out at a certain rpm, then i got looking on a parts diagram that the plastic gear mechanism on the side cover is the governor. i would have taken it out before but when i bought motor it said the governor was removed :bash: turns out it  wasnt. my question is how does that come out?

13
Honda and Clone Engines / Gx440 gen 2 adjustable flywheel
« on: April 18, 2014, 09:13:52 pm »
I was turning my motor over and it seems as the motor is firing to soon I have check the cam timin and valve lash. My only thing is the adjustable flywheel I have on it. It is set to the - side of the adjustment. Would spinning the flywheel more towards the + side crate a later spark?? Please any advice appreciated!

15
Chassis / is this carburator legal?
« on: March 02, 2014, 02:46:14 pm »
i have a mikuni slide carb. it is a 40mm. but im not all to sure that its legal for Super mod class. am i over looking the rule book and completely missing it? please help!!  :(

Pages: [1] 2