Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - offroadwhatever8

Pages: 1 2 [3] 4
31
Driveline / 2 speed jack shaft
« on: December 17, 2006, 06:11:06 pm »
Has any one ever used a 2 speed jack shaft in a mower or any thing?, I'm curious to know how good they work :confused:, thanks for the help

32
Driveline / What is your oppinion on a peerless 930-011 trans axle?
« on: December 13, 2006, 05:20:57 pm »
Today, i went out to one of my mower's which im gonne get running soon. I looked at the transaxle and it said modle 930-011 on the it, Its a 6 speed, Will this transaxle hold up to pulley changes?, here's a couple of pics.......Thank's for your help







33
Driveline / Pulley question.......
« on: December 11, 2006, 08:48:35 pm »
I'm about to ask the most stupidest question on the face of the planet, but when you measure a pulley to see what size it is, Do you measure from the outer rim of the pulley or from the inside where the belt groove is? thanks for the help.....

34
Post your Pics! / my huffy 5hp broad lawn
« on: December 09, 2006, 07:26:22 pm »
Here's my amzing huffy, soon to be a racer










i still have more pics,



35
Post your Pics! / quick pics of all of my mowers
« on: December 08, 2006, 05:56:19 pm »













these are just some really extremly quick pics i took to test out the new digital camera, I will try to get some better ones tomarrow.





36
Driveline / peerless diagrams
« on: December 06, 2006, 09:57:13 pm »
Is there any place besides http://www.odref.com/peerless/ , Im not saying that its bad, i just wish i could find some better diagrams on my 600 and 900.   

37
Driveline / Pulley won't come off
« on: December 06, 2006, 05:32:08 pm »
I just bought my 600 trans axle a few days ago and i can not get the pulley off, i spent a good 3 hours trying, but nothing. I have it the shaft soaking in liquid wrench overnight to see if it helps, Are there any good ways to get this pulley off?  thanks
















38
Tecumseh Engines / Govoner removal
« on: December 04, 2006, 03:16:52 pm »
How hard is it to remove a govoner in a 10 hp Tecumseh?, I have never removed a govoner in a Tecumseh or any other engine. What do I have to do? thanks for the help   -John

40
Driveline / more 600 questions.
« on: December 03, 2006, 05:40:06 pm »
What is a safe pulley change to run on a 600 with out blowing it up? thanks

41
Briggs Flathead / 5 hp horizontal engine carb
« on: November 24, 2006, 08:05:11 pm »
I was thinking about increasing the port size on my huffys carb like TheMowinCuban did to his mini bike, is this possible to do to my huffy? :confused:

42
Chassis / exhaust
« on: November 24, 2006, 12:00:46 am »
Dose any body have any good pictures of there exhaust?

43
Driveline / how hard is it to put a 600 on a craftsman
« on: November 22, 2006, 03:36:04 pm »
I was thinking about replacing my 900 with a peerless 600 on the back of my crapsman, how hard would it be to do this? Would it bolt right up with few modifications? :confused:

44
Driveline / 7/8 round axle shaft?
« on: November 21, 2006, 02:14:45 pm »
My huffy has a 7/8 axle on it and i cant find new bearings for it, i can olny find 7/8 hex bearings. Is there any specific places i could find 7/8 axcle and parts? :confused:, thanks for the help

45
Briggs Flathead / can a 5 hp swap some parts from a blown 12 hp
« on: November 18, 2006, 07:33:53 pm »
i was wonderine if there were any parts from a blown vertical 12 hp briggs could fit on my 5 hp vertical briggs?, im just trying to squese a little bit more out of my huffy, thanks for the help ;)

Pages: 1 2 [3] 4
anything