Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Topics - Burton for Certain

Pages: [1] 2
Driveline / fxs gear ratio
« on: May 06, 2013, 01:51:52 pm »
What kind of gear ratio yall run on a fxs with 15-8-8 hoosiers?

Coffee Shop / MWSC 1 1/8" clutch hub
« on: April 29, 2013, 11:03:43 pm »
Super Cub is making a run of 20 -1 1/8" replacement hubs for the bully turbo 1" clutch. Not sure on the price yet. You would buy the bully clutch and then buy the replacement hub from MWSC. So for all you billet crank boys, your dreams have almost come true!

Post your Pics! / 2013 Midwest Super Cub FXS (CUBZILLA)
« on: January 23, 2013, 06:35:33 pm »
Not doing a build thread, but ill post some pics as I go. Engine will be a 44 cube kohler command single cylinder. The two carbs that will be tested are a tilly hr-191 and a custom billet 44mm tilly from tillitson racing in Ireland. Diamond racing short skirt gas ported pistons. One off valvetrain. Full roller motor. No stock parts in this motor. It will be a horizontal shaft because I hate belts. This motor will be 8 more cubes than the motor I ran nationally in CP last year.

Post Your Video / Super Cub's Promo for IMIS 2012
« on: December 06, 2012, 12:51:34 pm »
Video put together for their booth. Features the Open Super Stock class which is diesels and twins pulling together. Gives some nice different points of view.

Our engine builder for the pulling tractors is the first tractor you see.

Garden Tractor Pulling / Spindles
« on: December 04, 2012, 02:01:06 pm »
Ok, so building our diesel puller. The engine is over top of the front axle and going to guess there's 450-550 lbs sitting on the front tires. The goal with this tractor is for the front end to not be on the ground. Most likely it will get slammed a lot. What would be the strongest for spindle and hoe to mount to the axle. Also trying to keep as light as possible.

« on: November 16, 2012, 11:53:11 am »
HOSTESS is filing Chapter 11 and liquidating assets. Laying off all 18,500 workers. Get the goodies before they're extinct. Horde them and in a few years make lots of $$$ selling them.

Okay, so I may really enjoy Twinkies. :rocknana:

Post Your Video / MWSC 45 cube puller
« on: October 06, 2012, 09:20:32 pm »
This is stahls personal tractor. They jumped it up to pull in the open superstock against their own 70 cube twin and the diesels. Ended up 3rd.

Post Your Video / 75 cube diesel
« on: October 06, 2012, 08:49:47 pm »
Russ Nichols on his 75 cube turbo diesel with water injection. 1100# with him on it. Still doesn't have a big enough turbo on it. Our engine that is being built currently will be a twin to his. Well over 350 ft/lbs of torque.

Post Your Video / US Finals Videos
« on: September 06, 2012, 12:33:09 pm »
Ok, I saw tons of go pros and people with cameras at finals. Let's see people start posting videos. I need something to hold me over til the SRAAUSO.

thank you kindly.

Post Your Video / Greensburg, PA
« on: August 19, 2012, 04:08:16 pm »
Cp Features. Ended up getting the win in both. Rookie camera operator in feature 1 and I forgot to turn the camera on until about halfway through the race in Feature 2.  I rolled the belt on its side in Feature 2 so I was just protecting the inside line because I knew Grover would be on me any minute.

Post Your Video / Sparta FXT Feature
« on: July 23, 2012, 09:55:19 am »

Coffee Shop / cost of a motor
« on: June 29, 2012, 09:02:35 am »
Ok, I hear everyone talking about how expensive Kohlers are compared to other motors. So how much do you guys spend on motors?

Coffee Shop / Rocketboy Racing Tires
« on: April 11, 2012, 09:15:30 pm »
Rocketboy Racing is looking to expand into mower racing. They previously had specialized in mini-sprints and dirt karts.

     They offer a 11-5.5-6 front wheel designed for multiple tracks. These tires have a rounded outer edge for the more extreme steering geometry that dirt karts and mowers use. The tread pattern is based off proven sprint car treads.


They also offer a 12-9-6 rear wheel that was designed for non-suspension racing equipment.

I will have a set of the rear wheels mounted at all of the races that I attend for anyone who would like to try them for hot laps, heat, or feature. This way you can try before you buy.

More information on these tires can be found at

Ask for Rodney Moses when you call.

Coffee Shop / pistol grip hot knife
« on: February 26, 2012, 03:39:29 pm »
Anybody know where I can get a decent one of these for a decent price. (Not $500) new or used, doesn't matter. I found cheap ones for under $100 but they look like throw away ones.

Coffee Shop / truckin
« on: February 20, 2012, 08:39:44 pm »
So for the next 3 weeks ill be hauling from Louisville to just north of Delaware Ohio via cincinnati and dayton. Im already tired of fast food and was wondering for suggestions of places to eat in the evenings. Thanks in advance. Im usually thru cincy around 600 and dayton around 700.

Pages: [1] 2