Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - FlatheadPuller

Pages: [1] 2 3 ... 7
1
Briggs OHV & Vanguard / 2bbl carb info
« on: November 14, 2015, 08:18:31 am »
Looking for info on 2bbl carbs. Possible part numbers and sizes of butterflies and venturis. I know Briggs has some, Kohler has a couple different ones and generac has one or 2.

2
Briggs Flathead / opposed machine work needed
« on: October 29, 2015, 05:07:37 pm »
I need a shop to do some valve and guide work on my oppsed. My local go to places cannot because the block won't fit there machines.

3
Briggs Flathead / opposed twin lifter diameter.
« on: September 29, 2015, 10:07:35 pm »
I'm talking with Isky about a cam for an opposed. I do not have my full pressure lube horizontal yet in my hands. Can someone give me the head diameter of an opposed twin lifter.

4
Briggs OHV & Vanguard / valve springs
« on: June 21, 2014, 07:23:53 pm »
Ec used to sell a kit for vangaurds. Springs and retainers. I can't find the kit anywhere on there website. Anyone know the part numbers needed?

5
Kohler Engines / Tillotsons on a command
« on: January 24, 2014, 07:48:00 pm »
Who is running twin tillys on a command? Looking for a base line for carb size. I am totally unfamiliar with tillotson carbs. Wanted to try them. Thanks for any help

6
Coffee Shop / Indoor arena in west michigan needed
« on: October 27, 2013, 09:00:06 pm »
I am looking for an indoor arena with a dirt floor to rent for a winter garden tractor pull. At least 150ft long.

Anybody?

7
Coffee Shop / Barry county expo center oct 19
« on: September 12, 2013, 07:40:29 pm »
Does everyone know about the racing there on Oct 19. I didn't see any posts about it yet. We will be there pullin as well.

8
Coffee Shop / Rod journal sizes
« on: April 20, 2013, 11:07:20 pm »
Is there a current engine you guys are racing with a 1.380 rod journal? If so what is it?

9
Garden Tractor Pulling / John Deere 12hp S/A
« on: February 26, 2013, 08:49:48 pm »
Im going to start a build thread on my sons new altered I am building him. He is moving up from the stock class. This tractor is a total build from the ground up. I had frame rails stamped in the correct cub cadet sizes but 56 inches long. 12hp kohler. .050 over, billet rod and Arias piston. 340/292 vogel steel cam. MWSC ready to run billet head. 19lb flywheel. Reworked stock carb.
















The wheelie bars and hitch I had a friend build for me. Machinest buddies. Zach Kerber cut the writing out in the front crossmember and under trans wieght box. I built everything else. Working on the steering tower now.

10
Non-Affiliated Races / Michigan Garden Tractor Pulling Championships
« on: January 21, 2013, 08:50:59 pm »
Rules for Michigan Tractor Pulling Championships. Trying to get a big pull started in Michigan. Going to be a yearly event. Rules are trying to allow alot of clubs in michigan that done have the same rules to co-exist and pull together plus NQS guys.

11
Driveline / Kart clutches
« on: January 17, 2013, 07:38:21 pm »
Curious as to how much torque you guys are putting thu the kart clutches. Do they lock up eventually or are they always slipping a little.I am looking to talk with someone on the phone about the kart clutches. I am wondering what they will take and if they would take being used on my sons pulling tractor with a 35-1 to 40-1 gear reduction.

12
Coffee Shop / Columbus winter pull
« on: December 07, 2012, 07:25:55 pm »
Who here is going to the winter championship pull in Columbus?

13
Garden Tractor Pulling / Our 45cid open S/S
« on: September 27, 2012, 09:45:59 pm »
This is our S/S tractor. Posted a few pics of this before but we have made some changes. Had some hiccups this season and finally got it right.


14
Honda and Clone Engines / 390 flywheel
« on: September 15, 2012, 04:24:04 pm »
Anybody have a 390 flywheel they can measure the O.D.  of and the thicknes when laying on a bench. Otherwise I have to take my engine of and dismantle to measure my flywheel. Mine is an electric start as well.

Thanks  Dennis

15
Honda and Clone Engines / GX 390 or clone 390 compression ratio
« on: September 09, 2012, 07:17:42 pm »
What I have found is the clone factory compression ratio is around 8.1-1. Anybody know what they are after a flattop is installed?

Pages: [1] 2 3 ... 7
anything