Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - VICTORVIKING 713

Pages: [1]
1
Briggs Flathead / Mods to 28 ci flathead?
« on: June 26, 2021, 08:22:37 am »
Hello there, people of the internet! I just pick up my first spare engine so I'm going to build it up and I come to you guys wondering what so you do to your flatheads? I'm going to source a billet flywheel and hopefully a billet rod for peace of mind and I've been doing some porting and polishing but what else do you guys do?

2
Oh okay cool. Thankyou!

3
Driveline / Re: peerless 820 transaxle
« on: May 06, 2021, 10:57:04 am »
Wow thank you so much!

4
Briggs OHV & Vanguard / Re: Leaving a vtwin vanguard governed
« on: May 03, 2021, 02:08:14 am »
Thank you

5
Briggs OHV & Vanguard / Leaving a vtwin vanguard governed
« on: April 27, 2021, 02:08:25 am »
I was wondering if it would be possible to mildly upgrade a vtwin but leave it governed but adjust it to rev higher oh and are ratio roller rockers a good up grade to wake up a vanguard a bit?

6
Briggs OHV & Vanguard / Re: Vtwin vanguard flywheels
« on: April 17, 2021, 12:28:23 am »
I'm gonna look more into it later to see if I can find something that might work.

7
Briggs OHV & Vanguard / Re: Vtwin vanguard flywheels
« on: April 16, 2021, 10:06:40 am »
Off roading, I don't want to be out on a trail and not be able to get my mower running again, I also have stuff on my mower that draws power such as a DC outlet, lights, volt meter and a couple of other things, I'm just looking for other options other then removing the charging system or running an external system.

8
Briggs OHV & Vanguard / Vtwin vanguard flywheels
« on: April 13, 2021, 08:53:13 am »
So I am wanting to spin my mower faster than stock however I want to keep my stock charging system. If I had enough room I would get a biullet flywheel and an alternator but it's a small Murray with a lack of room so I was wondering is there another way that doesn't risk my manhood?

9
Driveline / Re: peerless 820 transaxle
« on: April 04, 2021, 12:00:14 am »
Thank you so much!

10
How are they different? Does the Kohler have the same issues as the Briggs and what are some upgrades that can be done to a Kohler Opposed?

11
Driveline / Re: peerless 820 transaxle
« on: April 02, 2021, 04:25:38 am »
Okay, thank you.

12
Driveline / Re: peerless 820 transaxle
« on: March 31, 2021, 12:12:24 am »
Thank you and one more question, I heard that you can put the gears from mst transaxles and 700 transmissions are interchangable, what is the fastest gear ratio you can get for them?

13
Driveline / peerless 820 transaxle
« on: March 29, 2021, 09:30:48 pm »
So I'm planning on putting a 820 in my viking/murray but I need a long shift shaft for it, can someone send me a part number or can i take the long shift shaft out of my spicer and put it in an 820?

14
So I recently put a Vanguard vtwin in my mower, however it is a 29ci engine and I was wondering what upgrades would be possible to it?
I'm looking more at low end torque over super high RPMS. I am however going to try and source a twin barrel carby off of a 20 HP and what is interchangable between 38ci and a 29ci?
Oh and before I forget my budget is open however I would like to try and keep it on the cheaper side but I don't mind paying for safety.

Pages: [1]
anything