1
Driveline / Re: Mounting a Star Clutch
« on: February 13, 2011, 01:10:43 pm »
Thanks George, Your The Greatest! Dave
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
3
Driveline / Re: Mounting a Star Clutch
« on: February 13, 2011, 11:18:08 am »
I am mounting it on the motor (lock collars sounds like a good idea Thanks). How did you attach your pully to the gearbox input (mine only has a hole in it to accept a roll pin)?
4
Driveline / Mounting a Star Clutch
« on: February 12, 2011, 11:14:49 pm »
I am setting up my first mower using a Noram Star clutch on a vertical shaft engine to a RAGB. My question is do you put a spacer between the top of the clutch and the shoulder on the crank? If yes, how tight? Did you have a keyway cut on the RAGB input shaft? Any other advice you could give on this setup would be greatly appreciated. 
Thanks Dave
Thanks Dave
5
Tecumseh Engines / Re: TVM 220 Counter Balancer
« on: December 28, 2010, 08:29:29 pm »
Hold up ok?
6
Tecumseh Engines / TVM 220 Counter Balancer
« on: December 28, 2010, 08:26:28 pm »
Has anyone ever tried to build/run a TVM 220 without the counter balancer?
7
Racing Mower Builds / Re: My first ARMA legal mower
« on: October 12, 2009, 10:59:16 pm »
Jed, I am about to start mine! Anything you would do differently? How's it holding up? Dave
8
Racing Mower Builds / Re: Pro-X for 08
« on: October 12, 2009, 10:49:27 pm »
George, Getting ready to order parts and get started with mine! Anything you would do differently? How's it holding up? What clutch do you recommend? Dave
9
Racing Mower Builds / Re: My 09 build for the river rats club
« on: February 22, 2009, 09:12:56 pm »
Looking Good, Is it just me, or is your tranny going to run backwards ? Dave
10
Racing Mower Builds / Re: My brothers new mini sportsman - a/p
« on: August 04, 2008, 09:34:29 pm »
Nice work boy's!
11
Driveline / Re: gear box question
« on: August 04, 2008, 06:01:26 pm »
Same as any other ratio calculations... RAGBratio/(F/B)x(A/D)
Dave
Are you asking about a right angle gear box vs. the 516 tranny...??? Most are set up with a 1:1 ratio thru the box... some have a 2:1 ratio... but none run a 9:1Randy could you break this down in idiot terms for me? I am about to start building an F/X with a peerless RAGB 1:1, 12x8x6 rear cart tires. I have no idea what kind of final ratio you need to be competitive on the national circut? Any advice you could offer me would be greatly appreciated!
Same as any other ratio calculations... RAGBratio/(F/B)x(A/D)
Dave
12
Post your Pics! / Re: Starting my first build Any advise welcome
« on: July 15, 2008, 11:34:23 pm »
My buddy has two of these mowers running in the USLMRA . One is an A/P and one is an S/P!
Dave
Dave
13
Racing Mower Builds / Re: My first ARMA legal mower
« on: July 02, 2008, 12:01:14 am »
How wide are your wheels and what brand are they? Yea, George really knows his stuff, He built the motor on my S/P and still running strong after 2 1/2 years!
14
Racing Mower Builds / Re: My first ARMA legal mower
« on: July 01, 2008, 11:44:16 pm »
Very nice Jed ! You are making it hard for me to wait until winter to build mine though ! I like your wheel and tire look, What brand and size are you running ? What kind of bearing cassettes are those? What are you running on your's George? (wheels & tires)
Again good job Jed ! By the way I am from Jonesboro - Arkansas.
Dave
Again good job Jed ! By the way I am from Jonesboro - Arkansas.
Dave
15
Post your Pics! / Re: My new "USED" trailer
« on: May 24, 2008, 08:14:36 pm »
Very nice Tom! It does not get any cheaper than that for an enclosed trailer.