16
Driveline / Re: Gearbox lube
« on: September 29, 2015, 12:16:12 am »
Thanks guys
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
17
Driveline / Gearbox lube
« on: September 28, 2015, 09:26:23 am »
I'm just getting into the gearbox racing seen. What's the best lube and amount I should run in my 700 tranny. Thsnks, boxcar
18
Coffee Shop / FXT weight
« on: August 28, 2015, 08:30:03 am »
Whats the average weight of a FXT without driver. Thanks, boxcar
19
Driveline / Re: 40 chain master link
« on: July 26, 2015, 09:22:44 pm »
That's the way I've been running it. Just wanted to make sure.. Thanks everyone for the help
20
Driveline / Re: 40 chain master link
« on: July 26, 2015, 04:27:59 pm »
Should clip opening face towards the front or rear. Or doesn't it really matter
21
Driveline / 40 chain master link
« on: July 26, 2015, 12:25:00 pm »
Is their a right way/wrong way in which the clip opening faces. Thanks, boxcar
22
Driveline / Re: Gear ratio conversion
« on: July 06, 2015, 07:10:04 am »
Thanks, I didn't realize I'd have to go so small on the gearbox.
23
Driveline / Gear ratio conversion
« on: July 05, 2015, 07:20:05 pm »
Ok here I go, I have a 8" pulley on my motor, a 6" on a 1.92 to 1 gearbox. Right now I'm running a 12t driver to a 44t axle sprocket with 15" rear tires. I want to convert my belt to a chain clutch on motor and sprocket on gearbox. What am I running now and what should I buy for teeth on clutch and teeth on gearbox??? Does this make since to you all 
Thanks, boxcar
Thanks, boxcar
24
Coffee Shop / Digatron DT-32 K1
« on: June 07, 2015, 03:15:29 pm »
I've read the manual online to set the tach. Done everything it said to do. I get rpm numbers, but they don't seem right. Anyone run one of these. It's a Intek twin. Thanks, boxcar
25
Briggs OHV & Vanguard / Billet Flywheel
« on: May 11, 2015, 07:49:57 am »
Hey everyone, where can I purchase those little lock washers for the timing allen bolts for the billet flywheel??
Thanks
Thanks
26
Coffee Shop / perfect size track
« on: February 10, 2015, 08:38:24 am »
I was wondering what all you consider the perfect size oval dirt track. It would be nice if someone could post a blueprint of their track. Their is Possibly a new track that might be built a couple hours from me and they have a meeting coming up for some input. Thanks, boxcar
27
Briggs OHV & Vanguard / Complete seal rings (gapless)
« on: January 08, 2015, 07:20:41 pm »
Where can a guy buy these.
28
USLMRA Races / Re: Helments
« on: January 05, 2015, 08:07:17 pm »
2010 helmets expire this coming fall. I believe the 2015 ones come out in September if I remember right. Snell ratings are good for 5 years, so the 15's will be good till 2020
30
Tires / Golf cart rims
« on: December 08, 2014, 04:55:59 am »
Are they strong enough with out bracing??